COLO or Coarse Grain Lock Stepping is an High Availability solution that builds on top of Remus. Remus was prepared for use with COLO in Xen 4.5. The COLO Manager component is part of Xen 4.7, while other components will eventually be part of QEMU.

Background

COLO FT/HA (COarse-grain LOck-stepping Virtual Machines for Non-stop Service) project is a high availability solution. Both primary VM (PVM) and secondary VM (SVM) run in parallel. They receive the same request from client, and generate response in parallel too. If the response packets from PVM and SVM are identical, they are released immediately. Otherwise, a VM checkpoint (on demand) is conducted. The idea is presented in Xen summit 2012, and 2013, and academia paper in SOCC 2013.

Components

COLO Manager:

COLO Checkpoint/Failover Controller

Modifications of save/restore flow to realize continuous migration, to make sure the state of VM in Secondary side

always be consistent with VM in Primary side.

COLO Block Replication: (Please refer to BlockReplication)

When primary VM writes data into image, the colo disk manger captures this data

and send it to secondary VM’s which makes sure the context of secondary VM's image is consentient with

the ontext of primary VM 's image.

COLO Proxy:

We need an module to compare the packets returned by Primary VM and Secondary VM

and decide whether to start a checkpoint according to some rules.

In previous version. COLO Proxy is a linux kernel module for host. Because of this module

can't accepted by kernel community,you have to apply some patches to linux kernel and compile it yourself.

No support has been provided to kernelspace COLO Proxy.

In current version.COLO Proxy is a part of Qemu, all codes running in userspace. The filter-redirector, filter-mirror,

colo-compare and filter-rewriter compose the COLO-proxy. We can get better performance with COLO-proxy's help.

Compare with previous kernelspace COLO-Proxy, no more additional job to do, you just need ensure your qemu version support COLO Proxy.

Current Status

COLO (based on xm) has already been in development for over three years. A paper has come out at 2013. Since XEN has deprecated xm and turn to xl, we are implementing COLO on xl now. The overall status of COLO:

COLO Manager (Merged since 4.7.0-rc1):
COLO Block replication (Merged by Qemu)
COLO Proxy (Userspace COLO Proxy has been merged by Qemu)

The legacy kernelspace COLO Proxy View on Github

Requirements

Hardware requriements

There is at least one directly connected nic to forward the network requests from client to secondary vm. The directly connected nic must not be used by any other purpose. If your guest has more than one nic, you should have directly connected nic for each guest nic. If you don't have enough directly connected nic, you can use vlan.

Dom0 requirements

Kernel with dom0 support
If your host os has OEM-released xen tools, please uninstall it
Use latest Qemu version call for Xen

(Because have some COLO module communication related patches haven't be merged, you can use internal version: View on Github )

Guest requirements

Only HVM guest(without pv extensions) is supported now. If you want to use OEM released guest os, please use SUSE. REDHAT and Ubuntu is not supported now because I don't find any way to disable pv extensions. If you want to use REDHAT or Ubuntu, you need to build the newest kernel which has the parameter xen_nopv.

Setup COLO environment

Network link topology

=================================normal ======================================
                                +--------+
                                |client  |
         master                 +----+---+                    slave
-------------------------+           |            + -------------------------+
   PVM                   |           +            |                          |
+-------+         +----[eth0]-----[switch]-----[eth0]---------+              |
|guest  |     +---+-+    |                        |       +---+-+            |
|     [tap0]--+ br0 |    |                        |       | br0 |            |
|       |     +-----+  [eth1]-----[forward]----[eth1]--+  +-----+     SVM    |
+-------+                |                        |    |            +-------+|
                         |                        |    |  +-----+   | guest ||
                       [eth2]---[checkpoint]---[eth2]  +--+br1  |-[tap0]    ||
                         |                        |       +-----+   |       ||
                         |                        |                 +-------+|
-------------------------+                        +--------------------------+
e.g.
master:
br0: 192.168.2.98
eth1: 192.168.1.33
eth2: 192.168.3.1

slave:
br0: 192.168.2.99
br1: no ip address
eth1: 192.168.1.88
eth2: 192.168.3.2

===========================after failover=====================================
                                +--------+
                                |client  |
    master (dead)               +----+---+                 slave (alive)
-------------------------+           |            ---------------------------+
  PVM                    |           +            |                          |
+-------+         +----[eth0]-----[switch]-----[eth0]-------+                |
|guest  |     +---+-+    |                        |     +---+-+              |
|     [tap0]--+ br0 |    |                        |     | br0 +--+           |
|       |     +-----+  [eth1]-----[forward]----[eth1]   +-----+  |     SVM   |
+-------+                |                        |              |  +-------+|
                         |                        |     +-----+  |  | guest ||
                       [eth2]---[checkpoint]---[eth2]   |br1  |  +[tap0]    ||
                         |                        |     +-----+     |       ||
                         |                        |                 +-------+|
-------------------------+                        +--------------------------+

Test environment prepare

On both Primary/Secondary hosts:

checkout necessary repos:

# cd ~
# git clone https://github.com/xen-project/xen.git
# git clone https://github.com/zhangckid/qemu.git

Build and install xen

# cd ~/xen 
# ./autogen.sh; ./configure --enable-debug
# make dist-xen; make install-xen
# make dist-tools; make install-tools

Build qemu

# cd ~/qemu
# git checkout qemu-colo-for-xen
# cd ~/xen/tools/qemu-xen-dir
# ./configure --enable-xen --target-list=x86_64-softmmu \
              --extra-cflags="-I~/xen/tools/include -I~/xen/tools/libxc -I~/xen/tools/xenstore" \
              --extra-ldflags="-L~/xen/tools/libxc -L~/xen/tools/xenstore"
# make $(grep -c processor /proc/cpuinfo)

Note: You must use qemu that we provide, qemu-xen and qemu-xen-traditional are not supported.

On Primary host:

guest config

Add "xen_platform_pci=0" and below disk/net config into the guest configfile.

disk = [ 'format=raw,devtype=disk,access=w,backendtype=qdisk,vdev=hda,colo,colo-host=192.168.3.2,colo-port=9001,colo-export=qdisk1,active-disk=/mnt/ramfs/active_disk.img,hidden-disk=/mnt/ramfs/hidden_disk.img,target=/home/zhangchen/suse-64hvm-zc.img']
vif = [ 'mac=00:16:4f:00:00:11, bridge=br0, model=rtl8139, colo_sock_sec_redirector0_id=red0,colo_sock_sec_redirector0_ip=192.168.2.98,colo_sock_sec_redirector0_port=9003,
colo_sock_sec_redirector1_id=red1,colo_sock_sec_redirector1_ip=192.168.2.98,colo_sock_sec_redirector1_port=9004,
colo_filter_sec_redirector0_queue=tx,colo_filter_sec_redirector0_indev=red0,colo_filter_sec_redirector1_queue=rx,
colo_filter_sec_redirector1_outdev=red1,colo_filter_sec_rewriter0_queue=all,colo_sock_mirror_id=mirror0,colo_sock_mirror_ip=192.168.2.98,
colo_sock_mirror_port=9003,colo_sock_compare_pri_in_id=compare0,colo_sock_compare_pri_in_ip=192.168.2.98,colo_sock_compare_pri_in_port=9021,
colo_sock_compare_sec_in_id=compare1,colo_sock_compare_sec_in_ip=192.168.2.98,colo_sock_compare_sec_in_port=9004,colo_sock_compare_notify_id=not1,
colo_sock_compare_notify_ip=192.168.2.98,colo_sock_compare_notify_port=9998,colo_sock_redirector0_id=compare_out,
colo_sock_redirector0_ip=192.168.2.98,colo_sock_redirector0_port=9005,colo_sock_redirector1_id=compare0-0,colo_sock_redirector1_ip=192.168.2.98,
colo_sock_redirector1_port=9021,colo_sock_redirector2_id=compare_out0,colo_sock_redirector2_ip=192.168.2.98,colo_sock_redirector2_port=9005,
colo_filter_mirror_queue=tx,colo_filter_mirror_outdev=mirror0,colo_filter_redirector0_queue=rx,colo_filter_redirector0_indev=compare_out,
colo_filter_redirector1_queue=rx,colo_filter_redirector1_outdev=compare0,colo_compare_pri_in=compare0-0,colo_compare_sec_in=compare1,
colo_compare_out=compare_out0,colo_compare_notify_dev=not1,colo_checkpoint_host=192.168.2.98,colo_checkpoint_port=9998' ]

Copy physical machine disk image from Primary to Secondary，and make sure their absolute path are the same

Note: colo-port is the secondary host's IP, colo-port is the secondary host's NBD server port, forwarddev is the directly connected nic.

Run COLO

On both Primary/Secondary hosts:

# service xencommons start

On Secondary host: excute the following script:

#! /bin/bash

active_disk=/mnt/ramfs/active_disk.img
hidden_disk=/mnt/ramfs/hidden_disk.img
local_img=~/suse-64hvm.img
tmp_disk_size=`./qemu-colo/qemu-img info $local_img |grep 'virtual size' |awk  '{print $3}'

function create_image()
{
    ~/qemu/qemu-img create -f qcow2 $1 $tmp_disk_size 
}

function prepare_temp_images()
{
    grep -q "^none /mnt/ramfs ramfs" /proc/mounts
    if [[ $? -ne 0 ]]; then
        mount -t ramfs none /mnt/ramfs/ -o size=2G
    fi

    if [[ ! -e $active_disk ]]; then
        create_image $active_disk      
    fi

    if [[ ! -e $hidden_disk ]]; then
        create_image $hidden_disk
    fi
}

prepare_temp_images

Note: It is recommended to put active disk and hidden disk in ramdisk.

On Primary host:

# xl create -p <domconfig>
# xl pause <domconfig>
# xl remus -c -p -u <domconfig> 192.168.3.2

Known problems

Secondary vm may crash due to triple fault.

Note: this problem doesn't happen every time. So you can run colo again to avoid this problem.

Trouble shooting

If there's some error happend when staritng COLO, you can do:

Make sure you have all necessary modules that DOM0 needed on both side.
Make sure you have followed all the instructions in this README.
Try to reboot both primary and secondary host.
If you still have problems, collect the error logs and contact Zhang Chen(zhangckid@gmail.com), Xie Changlong(xiecl.fnst@cn.fujitsu.com),
Wen Congyang(wency@cn.fujitsu.com), Yang Hongyang(imhy.yang@gmail.com) for help.

Example

If you use SLES11.3, you can get the detailed steps from the wiki: Setup COLO on SLES11 SP3

An example guest config:

builder='hvm'
memory='2048'
vcpus=2
cpus=['2','3']

name='hvm_nopv_colo'
device_model_version='qemu-xen'
device_model_override='/home/zhangckid/qemu/x86_64-softmmu/qemu-system-x86_64'

disk = [ 'format=raw,devtype=disk,access=w,backendtype=qdisk,vdev=hda,colo,colo-host=192.168.3.2,colo-port=9001,colo-export=qdisk1,active-disk=/mnt/ramfs/active_disk.img,hidden-disk=/mnt/ramfs/hidden_disk.img,target=/home/zhangchen/suse-64hvm-zc.img']
vif = [ 'mac=00:16:4f:00:00:11, bridge=br0, model=rtl8139, colo_sock_sec_redirector0_id=red0,colo_sock_sec_redirector0_ip=192.168.2.98,colo_sock_sec_redirector0_port=9003,
colo_sock_sec_redirector1_id=red1,colo_sock_sec_redirector1_ip=192.168.2.98,colo_sock_sec_redirector1_port=9004,
colo_filter_sec_redirector0_queue=tx,colo_filter_sec_redirector0_indev=red0,colo_filter_sec_redirector1_queue=rx,
colo_filter_sec_redirector1_outdev=red1,colo_filter_sec_rewriter0_queue=all,colo_sock_mirror_id=mirror0,colo_sock_mirror_ip=192.168.2.98,
colo_sock_mirror_port=9003,colo_sock_compare_pri_in_id=compare0,colo_sock_compare_pri_in_ip=192.168.2.98,colo_sock_compare_pri_in_port=9021,
colo_sock_compare_sec_in_id=compare1,colo_sock_compare_sec_in_ip=192.168.2.98,colo_sock_compare_sec_in_port=9004,colo_sock_compare_notify_id=not1,
colo_sock_compare_notify_ip=192.168.2.98,colo_sock_compare_notify_port=9998,colo_sock_redirector0_id=compare_out,
colo_sock_redirector0_ip=192.168.2.98,colo_sock_redirector0_port=9005,colo_sock_redirector1_id=compare0-0,colo_sock_redirector1_ip=192.168.2.98,
colo_sock_redirector1_port=9021,colo_sock_redirector2_id=compare_out0,colo_sock_redirector2_ip=192.168.2.98,colo_sock_redirector2_port=9005,
colo_filter_mirror_queue=tx,colo_filter_mirror_outdev=mirror0,colo_filter_redirector0_queue=rx,colo_filter_redirector0_indev=compare_out,
colo_filter_redirector1_queue=rx,colo_filter_redirector1_outdev=compare0,colo_compare_pri_in=compare0-0,colo_compare_sec_in=compare1,
colo_compare_out=compare_out0,colo_compare_notify_dev=not1,colo_checkpoint_host=192.168.2.98,colo_checkpoint_port=9998' ]

#-----------------------------------------------------------------------------
# boot on floppy (a), hard disk (c), Network (n) or CD-ROM (d) 
# default: hard disk, cd-rom, floppy

boot='c'
sdl=0
vnc=1
vnclisten=''
stdvga = 0 
serial='pty'
apic=1
apci=1
pae=1
extid=0
keymap='en-us'
localtime=1
hpet=1
usbdevice='tablet'
xen_platform_pci = 0

Man Pages

Links

For more information see:

COLO - Coarse Grain Lock Stepping

Contents

Background

Components

Current Status

Requirements

Hardware requriements

Dom0 requirements

Guest requirements

Setup COLO environment

Network link topology

Test environment prepare

Run COLO

Known problems

Trouble shooting

Example

Man Pages

Links

Navigation menu

Page actions

Page actions

Personal tools

WIKI GUIDE

Search

NAVIGATION BY INDEX

NAVIGATION BY AUDIENCE

HYPERVISOR & TOOLS

EMBEDDED/AUTOMOTIVE

UNIKERNELS

COMMUNITY

NAVIGATION BY DOC TYPE

NAVIGATION BY TECHNOLOGY

INTERACTION

Tools